- #Kenwood tk 880 firmware update
- #Kenwood tk 880 firmware full
- #Kenwood tk 880 firmware software
- #Kenwood tk 880 firmware series
The face plate is reversible allowing the speaker to be on the top or bottom of the radio (depending on installation option). They also support PA (Public Announcement) but require a special plug (KCT-19) and Voice Inversion Scrambling support which also requires an option board to be installed. You can also link them to a computer and send short messages to a remote radio over Fleetsync or a pre-defined message using the buttons on the front panel to a specific station or all stations (All Call). All from using DTMF signaling from a remote station. Remote Honk Alert with confirmation tone, Remote disable/enable TX, and Radio disable/enable with confirmation tone. The radio also has scan support and this works with LTR and conventional channels. These radios do support Fleetsync Enhanced Protocol and allow for unit to unit calling and Radio (Caller) ID Support.
#Kenwood tk 880 firmware full
However, if the radio is used to its full potential using a Ham Repeater or Commercial LTR Repeater you can easily stretch 100 miles or more depending on the repeater height and configuration. They can very easily go much further the higher up you are. Using a roof top mag mount Antenna, I've been able to talk from Vehicle to Vehicle up to 10 miles away (Simplex on flat ground non-obstructed (I was on the highway at the time)). The radio is able to be programmed down to the 440Mhz range (70cm HAM) along with GMRS and of course UHF Commercial frequencies (which was the radio's intent). I chose to flash the radio back to the latest Kenwood firmware.
#Kenwood tk 880 firmware software
To make these radios work you will need to order a programming cable, however, he does have the software required to change the programming of the radio. He has been extremely helpful with these radios. So far I've ordered 2 of these radios from this seller. HH-31X belt pack interface module for single plug (UH-10 / FH-10 Firecom headsetsįor 500-Series wireless headsets and ComHubs.Kenwood TK-880-H1 w/ SJI Firmware from Hotfire! Through the DB-15 pin accessory port: Will need to program pin #6 for PTT and change R806 from a 100K to 10K, The resistor change will change the DI input to MI input or from digital to analog. (Use p/n 110-5165-30) Through accessory port Remove jumper J1 in the KMC35 hand microphone for hot Mic fix Through 25 pin accessory port, move R641 to R640 for mic input, program A/I # 1 to "PTT Audio" KMC35 mic will need to do Hot mic Fix, remove JP-1 inside mic change programming under "Function Port" tab under "Input" to "Head" on A/I # 1, Set pin #6 to "External PTT". Remote including dual band through accessory portĭual band through remote head 12 pin accessory port. Remove jumper J1 in microphone for hot Mic fix
#Kenwood tk 880 firmware series
TK-5730 / TK-5830 series with 19M / KCH-20R remote head (Use p/n 110-5160-30) PTT through the accessory port pin 13.
This resolves the issue of the mic not working with KCT-72 enabled.
#Kenwood tk 880 firmware update
When using a MR-47X with a KCT-72 adaptor, You will need to do a firmware update to the radio using the JKCA170 firmware update from Kenwood. They will need to do a firmware update to the radio using the JKCA170 firmware update from Kenwood. Programming will need to be set to "control head mic input" "KCT-72"using a MR-47X with a KCT-72 adaptor. This will work with up to 3 transceivers connected to the head and RX Audio will be available through the MR-47X to the intercom. If using the Kenwood KCT-72 adaptor for the MR-47X to plug into, it will disable the hand mic from working unless the firmware update is done. TK-5000 / NX-5000 series with 19M / KCH-20R remote head Need to program pin 5 for "PTT audio" and inside the radio move R797 to R799.
(Use p/n 110-5160-30) Will need to program like a 5710, set pin 13 to "External PTT Voice" and pin 6 to "connect" under MI2 Line. NX-700 / NX-800 / NX-900 Through accessory port Will need to remove (R659 & R612) and add jumpers to (R601 & R613)
KRK-5DH, 6DH, 7DH, 8DH through the accessory port Will need to connect the blue & green wires to the 3.5mm jack
0 kommentar(er)
